Need help?

Press the button on the front of the unit until the LED flashes red 5 times.

Eve Aqua’s standard 26.5 mm / ¾" thread fits virtually any regular outdoor faucet. When fitting Eve Aqua, screw it all the way on to the faucet using your fingers. Ensure it fits securely and that no water escapes even when the valve is shut.

Adding HomePod mini to your home means Thread-enabled Eve accessories such as Eve Aqua (2nd generation) can communicate via Thread – the mesh network that reaches even the farthest corners of your abode. This happens automatically without you needing to configure anything. Simply position a Full Thread Device, such as Eve Energy (EU), as close as possible to your Eve Aqua. The Eve Energy accessory will then act as a router and relay data packets from Eve Aqua.

Once set up, Eve Aqua works completely autonomously. It’s entirely up to you if you want to use the HomeKit automation and remote access functions that require a home hub.

Yes, standard threads on both connectors, a hose adapter, and a pressure range of Min 1 bar / Max 5 bar ensure compatibility with any common irrigation equipment.

While Eve Aqua is weatherproof and UV resistant, you should prevent it from freezing up, just like your hoses and sprinklers.

Using a water flow meter (starting at USD $20) is the most convenient way. Alternatively, use a measuring bucket to collect a minute’s worth of water from each outlet in your system.

Use a paper clip or similar object to press the "Reset" button on the back of the enclosure for more than 10 seconds. Release the Reset button immediately. Eve Button should now be reset.

Use a paper clip or similar object to press the reset button.

Make sure that either the 2.4 gigahertz band or the 5 gigahertz band is enabled on your router. The DHCP function must be activated on the router. Authentication via MAC addresses must be deactivated.

All Wi-Fi-based devices with HomeKit support require the Bonjour protocol (Multicast) to work. Make sure that Bonjour and Multicast are enabled on the Wi-Fi router and additional access points.
Network tools such as "Storm Control" and others, allow multicast to be restricted and therefore Bonjour. Disable this setting.
So-called Powerline/PowerLAN adapters also restrict Bonjour or do not allow it. These access points are not suitable for the use of HomeKit-based Wi-Fi devices.

Eve Cam supports HomeKit Secure Video, allowing you to securely save the events your camera detects. Using the Apple Home app, you can view your camera’s live feed or recordings on your iPhone at any time. Learn more

Please make sure that DHCP is enabled on your router. Authentication via MAC addresses must be deactivated. WPA2 must be activated, not the legacy WPA/WPA2 mode. After adjusting any settings, please restart your router and wait a few of minutes. Afterwards, please reset Eve Cam.

Eve Cam features a dedicated infrared motion sensor to trigger motion alerts, automations and recordings. If you have configured people / pet / vehicle recognition, any motion detected by the infrared motion sensor will cause the video footage to be sent to your Apple TV or HomePod to intelligently determine whether your recording criteria is met. Please note that while the infrared motion sensor can "see" in the dark, it can't see through glass. So if there's a glass door to your front porch or there's a window looking out to your patio or yard, Eve Cam won't detect any motion behind it and thus also not trigger notifications, automations or recordings.

• Press the button once to activate Eve Degree. Thereafter press the button to toggle between temperature and humidity on the screen.
• Eve Degree works wonders when simply placed on any surface, or mounted on a wall.
  Thanks to IPX3 water resistance, even outdoor locations exposed to a little rain are suitable.
• Download the Eve app from the App Store.

• Open the Eve app and tap Add Accessory. Eve will now guide you through the
  setup process.

• If you have already set up another accessory, go to the Eve settings to add
  Eve Degree to your home.

• Press the "Reset" button on the back of the enclosure for more than 10 seconds until the LCD shows "-99.9"
• Release the Reset button immediately
• Eve Degree should now be reset

By default, Eve will use units that are common in your region. In iOS Settings > Eve > Units you can switch from ° C to °F, and from hPa to mbar or inHg. To change the temperature displayed on the front of Eve Degree from Celsius to Fahrenheit, navigate in Eve to Settings > Devices > Eve Degree.

You’ll need the Eve app to process measurements recorded by Eve Degree in a spreadsheet on your iOS device or computer. Double-tap a graph, select Measurements in the new screen, and tap the sharing icon to access the export function. Export creates an .xlsx file, so you can even use it in Numbers.
ou can even use it in Numbers.

There is a reset button inside the battery door. Use a paper clip or similar object to press it until the red LED is blinking.

Alongside Bluetooth, Eve Door & Window supports Thread. This technology makes your smart home network more responsive, robust, and increases its reach – the only thing you need is a HomePod mini or the new Apple TV 4K. Battery-operated Thread accessories, such as Eve Eve Door & Window represent endpoints in your Thread network. 

By contrast, mains-powered Thread accessories that are always on, such as Eve Energy (Europe, U.K., U.S. & Canada) and Eve Light Switch (Europe), can act as router nodes within your Thread network and relay data packets. So, the more of these Full Thread Devices (FTDs) you have in your network, the more stable and greater its reach becomes. Learn more

If you use Eve Door & Window on a window in the room where you’re also using Eve Thermo, Eve can automatically stop heating if the window is opened for ventilation purposes. It then resumes heating once the window is shut. The easiest way to set up this automation is to open the Eve app and tap Rooms > Eve Thermo > Automation > Window Detection. This type of automation requires a HomePod, HomePod mini or Apple TV as a home hub.

Yes, it is. All you need to do is stick the tiny magnet and miniscule 5-cm-/2"-wide sensor to any flat surface. It doesn’t even matter if your door’s recessed behind the frame, as Eve Door & Window includes super-useful spacers so you can line up the top of the magnet with the sensor for optimal performance. Eve Door & Window fits on your pet door, piano, refrigerator, garage door, window shutters and even your mailbox – the possibilities are endless.

There is a reset button for the accessory. Plug Eve Energy into the power outlet and press the reset button until the LED flashes red.

Alongside Bluetooth, Eve Energy (Europe, U.K., U.S. & Canada) supports Thread. This technology makes your smart home network more responsive, robust, and increases its reach – the only thing you need is a HomePod mini or the new Apple TV 4K. 

Mains-powered Thread accessories that are always on, such as Eve Energy (Europe, U.K., U.S. & Canada) and Eve Light Switch (Europe), can act as router nodes within your Thread network and relay data packets. So, the more of these Full Thread Devices (FTDs) you have in your network, the more stable and greater its reach becomes. By contrast, battery-operated Thread accessories, such as Eve Aqua, Eve Door & Window, Eve Room, Eve Thermo and Eve Weather represent endpoints in the Thread network (or Minimal Thread Devices – MTDs). Learn more

Yes. The little green LED is a button that you simply press. That way, whether your phone is out of reach, you don’t want to disturb the peace with a voice command, or a guest does not have access, Eve Energy can be operated like a regular switch.

Yes. Thanks to built-in terminal shutters that automatically close when unoccupied by a connected device, Eve Energy is off limits to budding electricians. Plus it features a child lock that disables the onboard button.

If the data on your Eve Energy Strip accessory displayed in the Eve app is incorrect, pull it out of its power outlet, wait 15 seconds, and then plug it back into the power outlet. This partial reset may solve some problems.

If this doesn't help, then you can use these steps to do a hard reset:
1. Plug Eve Energy Strip into a socket and wait until the 3rd LED power button stops blinking
2. Press the 1st and 3rd LED power buttons at least 10 s, until the 3 LEDs blink
3. Release the power buttons and wait until all LEDs stop blinking

Make sure the 2.4 gigahertz band is enabled on your router and that your iPhone is using the band to add the Eve Energy Strip. Later, you may reconnect your iPhone using the 5 gigahertz band. The DHCP function must be activated on the router. Authentication via MAC addresses must be deactivated.

All Wi-Fi-based devices with HomeKit support require the Bonjour protocol (Multicast) to work. Make sure that Bonjour and Multicast are enabled on the Wi-Fi router and additional access points.
Network tools such as "Storm Control" and others, allow multicast to be restricted and therefore Bonjour. Disable this setting.
So-called Powerline/PowerLAN adapters also restrict Bonjour or do not allow it. These access points are not suitable for the use of HomeKit-based Wi-Fi devices.

•  If the Eve Energy Strip was already added to the Eve App, delete it from the Eve App
• Disconnect the Eve Energy Strip from the power supply and wait 1 minute.
• Restart your iOS device completely.
• Disable and reactivate Wi-Fi under "Settings -> Wi-Fi" on the iOS device (note: use "Settings", not iOS Control Center).
• Connect the Eve Energy Strip to the power supply and wait 3 minutes.
• Carry out a complete reset of the Eve Energy Strip:
  1. Plug Eve Energy Strip into a socket and wait until the 3rd LED power button stops blinking
  2. Press the 1st and 3rd LED power buttons at least 10 s, until the 3 LEDs blink
  3. Release the power buttons and wait until all LEDs stop blinking
• (Re)pair the Eve Energy Strip over the Eve App.

1. Press the reset button and keep it pressed.
2. Connect the power supply to Eve Extend while continue to press the reset button.
3. Keep the reset button pressed for another 10 seconds, then release it.
4. When the red LED on the upper side of Eve Extend flashes, the reset has been done.

Make sure that either the 2.4 gigahertz band or the 5 gigahertz band is enabled on your router. The DHCP function must be activated on the router. Authentication via MAC addresses must be deactivated.

All Wi-Fi-based devices with HomeKit support require the Bonjour protocol (Multicast) to work. Make sure that Bonjour and Multicast are enabled on the Wi-Fi router and additional access points.
Network tools such as "Storm Control" and others, allow multicast to be restricted and therefore Bonjour. Disable this setting.
So-called Powerline/PowerLAN adapters also restrict Bonjour or do not allow it. These access points are not suitable for the use of HomeKit-based Wi-Fi devices.

All Bluetooth-enabled Eve accessories except Eve Thermo (2015) and Eve Room (2015), both without display. Due to technical reasons, a compatibility is not possible. Compatible accessories

Eight accessories. Any number of Eve Extend range extenders can be used to reach more Eve accessories.

No. If you use Eve accessories while you’re at home, Eve Extend will work perfectly without a home hub. If you wish to reach all your accessories remotely, and run automations, a home hub – HomePod or Apple TV – is mandatory.

Press the MODE button on the back of the unit until a color sequence starts.

Please find the Reset button in the hole on the side of the controller. Insert a straightened paper clip or similar object into the hole, and press the Reset button for at least 10 seconds. Release the Reset button immediately after the LEDs have blinked twice. Eve Light Strip is now reset.

Make sure the 2.4 gigahertz band is enabled on your router and that your iPhone is using the band to add the Eve Light Strip. Later, you may reconnect your iPhone using the 5 gigahertz band. The DHCP function must be activated on the router. Authentication via MAC addresses must be deactivated.

All Wi-Fi-based devices with HomeKit support require the Bonjour protocol (Multicast) to work. Make sure that Bonjour and Multicast are enabled on the Wi-Fi router and additional access points.
Network tools such as "Storm Control" and others, allow multicast to be restricted and therefore Bonjour. Disable this setting.
So-called Powerline/PowerLAN adapters also restrict Bonjour or do not allow it. These access points are not suitable for the use of HomeKit-based Wi-Fi devices.

• If the Eve Light Strip was already added to the Eve App, delete it from the Eve App.
• Disconnect the Eve Light Strip from the power supply and wait 1 minute.
• Restart your iOS device completely.
• Disable and reactivate Wi-Fi under "Settings -> Wi-Fi" on the iOS device (note: use "Settings", not iOS Control Center).
• Connect the Eve Light Strip to the power supply and wait 3 minutes.
• Carry out a complete reset of the Eve Light Strip:
• The reset button is located on the side in a small hole of the controller. Press the reset button with a paper clip or similar object for at least 10 seconds until the LEDs flash twice. Eve Light Strip is now reset.
• (Re)pair the Eve Light Strip over the Eve App.

To shorten Eve Light Strip, use a pair of scissors to cut along an indicated trim line (approximately every 30 cm). To lengthen, simply connect additional 2 m / 6.6 ft extension strips (available at the online Eve store). The maximum length to which you can extend Eve Light Strip is 10 m. Setup video & QSG.

Light emitted by LEDs is measured in lumens. The maximum lumen output of other brands’ LED strips is 1600 lumens at a lenght of 2 m / 6.6 ft. Eve Light Strip outputs 1800 lumens at 2 m /6.6 ft.

Not all LED strips are created equal. The most common strips feature single RGB diodes that produce multiple colors, or a single diode that emits white. Some combine a single RGB diode and a single white diode. By contrast, Eve Light Strip sports three separate diodes - one RGB, one cold white, and one warm white - all of which collectively or separately produce accurate colors and permit greater range to mix and blend shades.  

• Remove the switch plate by pulling the center plate evenly from both sides.
• Press both left buttons simultaneously for 10 seconds. 

Alongside Bluetooth, Eve Light Switch supports Thread. This technology makes your smart home network more responsive, robust, and increases its reach – the only thing you need is a HomePod mini or the new Apple TV 4K. 

Mains-powered Thread accessories that are always on, such as Eve Energy (Europe, U.K., U.S. & Canada) and Eve Light Switch (Europe), can act as router nodes within your Thread network and relay data packets. So, the more of these Full Thread Devices (FTDs) you have in your network, the more stable and greater its reach becomes. By contrast, battery-operated Thread accessories, such as Eve Aqua, Eve Door & Window, Eve Room, Eve Thermo and Eve Weather represent endpoints in the Thread network (or Minimal Thread Devices – MTDs). Learn more

No. Eve Light Switch accepts commands from regular light switches, like switches used in an existing alternating or cross-connection. You only need to replace the switch that is connected to the light.

Eve Light Switch requires knowledge of electrical wiring. Please ask an electrician for help. This is how Eve Light Switch is installed.

Eve Light Switch comes with a 55 mm switch plate and a compatible frame in a modern design. You can easily reuse your existing single or multi-switch frames as long as they are one of the 55 mm designs. Simply combine your existing frame with the included switch plate. Switch plates and frames compatible with other designs are sold separately here. Please note that your existing switch plate is not compatible with Eve Light Switch.

• First version of the product : Press the button with your finger until the yellow LED lights up. Then release the button.
• Second version of the product : Press the button with two fingers as shown in the image below until the yellow LED lights up. Then release the button.

• Eve Light Switch requires a neutral wire and replaces a single pole switch.
• Eve Light Switch is not intended for use in a 3-way installation where lights are controlled by more than one switch.

• Eve Light Switch does not act as a dimmer. It's either on, or off.
• Eve Light Switch requires a neutral wire and replaces a single pole switch.

There is a reset button inside the battery door. Use a paper clip or similar object to press until the red LED is blinking 5 times.

To reset all settings of Eve Outdoor Cam, including the HomeKit pairing, push and hold the reset button on the bottom of the camera with a paper clip for 10 seconds until the LED starts blinking red.

Make sure the 2.4 gigahertz band is enabled on your router and that your iPhone is using the band to add the Eve Outdoor Cam. Later, you may reconnect your iPhone using the 5 gigahertz band. The DHCP function must be activated on the router. Authentication via MAC addresses must be deactivated.

All Wi-Fi-based devices with HomeKit support require the Bonjour protocol (Multicast) to work. Make sure that Bonjour and Multicast are enabled on the Wi-Fi router and additional access points.
Network tools such as "Storm Control" and others, allow multicast to be restricted and therefore Bonjour. Disable this setting.
So-called Powerline/PowerLAN adapters also restrict Bonjour or do not allow it. These access points are not suitable for the use of HomeKit-based Wi-Fi devices.

Eve Outdoor Cam is best installed replacing an existing outdoor light and requires AC power with both a neutral wire and a connection to a ground wire. To see how easy it is to install Eve Outdoor Cam, watch the installation video.

Thanks to a dedicated motion sensor, Eve Outdoor Cam will not bother you with reacting to leaves blowing in the wind, small animals, and other events that do not require your attention. If you have configured people / pet / vehicle / package recognition, any motion detected by the infrared motion sensor will cause the video footage to be sent to your Apple TV or HomePod to intelligently determine whether your recording criteria are met.

Eve Outdoor Cam will automatically turn on the flood light when motion is detected by the dedicated motion sensor. To limit the automatic motion light to nighttimes, adjust the duration, or deactivate it altogether, access the accessory settings in the Eve app.

If you want the integrated flood light to shine extra-bright, tap the light boost button in the Eve app. You can also enable light boost for the automatic motion light. Light boost will turn off automatically after a period of time.

Simultaneously touch both capacitive controls until the reset icon appears on the display. Then press the Reset button on the back of Eve Room within 30 seconds.

If Eve Room continues to show implausible values, you may want to perform a soft reset. Just press the reset button on the back. If the device doesn’t resume normal functionality, please restore factory settings: Press and hold both arrow keys for a few seconds to bring up the reset icon. Within the next 30 seconds, press the reset button to reset the hardware.

The battery is probably deep discharged.

Please try the following:

• Connect Eve Room with the supplied cable and a suitable power supply like that of the iPhone or iPad and plug it into the power outlet.
• Wait 10 minutes.
• Press the reset button on the back of the Eve Room (2018) with an open paper clip for 10 seconds.
• Now let the Eve Room charge for a few hours.

Eve Room will determine a room’s air quality by contrasting a certain tVOC count against optimal conditions. Calibrating the sensor requires that you place Eve Room in different locations; one with ambient conditions and another that is exposed to fresh air. After the initial setup, place Eve Room in its future location for about 6 hours, then move it to a well-ventilated area for 30 minutes. Repeat this calibration process if you move the sensor to a different room.

If you want to restart the calibration process, you 1st need to remove the Eve Room from your home, hard reset it and pair it again to Eve app in order to start the calibration mode.

Eve Room uses state-of-the-art technology to provide near-exact measurements. Accuracy is ± 0.3 °C / ± 0.54 °F, ± 3% humidity. The gas sensor combines multiple sensing elements with long-term durability that is unprecedented for a commercially available product.

You’ll need the Eve app to process measurements recorded by Eve Room in a spreadsheet on your iOS device or computer. Double-tap a graph, select Measurements in the new screen, and tap the share icon to access the export function. Export creates an .xlsx file, so you can even use it in Numbers.

Volatile organic compounds (VOCs) are substances that contain carbon which are emitted as gases into the air. They can occur naturally (emissions from people, pets, or plants) or come from household items such as plastics, construction materials, furniture, carpets, wall paints, cleaning supplies, and tobacco smoke in your home. "Sick building syndrome" is the name given to a range of symptoms ranging from headaches, sleep disturbance, and a sore throat which occur due to high VOC concentrations.

When you’re in the room you’re monitoring, a quick glance at the clear 5-star scale tells you all you need to know. It’s also a breeze to add automations using the Home app (iOS 15.1 and later) and the Eve app which, when triggered by changes in air quality, can have a light change color or your HomePod play a sound. See here for some examples.

Alongside Bluetooth, Eve Room supports Thread. This technology makes your smart home network more responsive, robust, and increases its reach – the only other thing you need is HomePod mini or the new Apple TV 4K. Battery-operated Thread accessories, such as Eve Room, represent endpoints in your Thread network. 

By contrast, wall-powered Full Thread Devices (or FTDs) that are always on, such as Eve Energy (Europe, U.K., U.S. & Canada) and Eve Light Switch (Europe), can act as router nodes within your Thread network and relay data packets. So, the more of these Full Thread Devices (FTDs) you have in your network, the more stable and greater its reach becomes. Learn more

Press both Reset buttons inside Eve Smoke for 10 seconds - until the yellow LED starts blinking

You can use the Eve app to check that Eve Smoke is working perfectly - with a soft alarm that’s gentle on the ears (75 dB(A) at a distance of 1 m). An alarm test will not trigger a notification.

In case of a real alarm, Eve Smoke will alert you immediately with a loud alarm (85 dB(A) at a distance of 3 m) and by turning on the emergency light. You will hear a constant sound for a smoke alarm, and a sound/pause every second for a heat alarm. Eve Smoke will continue to alert you until no smoke or heat is detected, or until the alarm is silenced. If configured in the Apple Home App, you will also receive a notification.

You can mute Eve Smoke using the Eve app when Eve Smoke is in direct range. For your safety, an alarm cannot be muted using remote access. Muting an alarm using the Apple Home app is not possible. The alarm can also be muted by pressing the Test button on Eve Smoke or by pointing an infrared remote control towards Eve Smoke and pressing any button on the remote twice.

After muting an alarm, Eve Smoke will suppress the alert for 15 minutes. If smoke is still detected after 15 minutes, the alarm will sound again.

The acoustic and visual alarm of Eve Smoke cannot be deactivated.

• Eve Smoke has a battery life of 10 years.
• Once the batteries are discharged, you will not be able to continue using Eve Smoke.
• It is not possible to change the batteries, they are soldered on the electronic board.
• The sensors also have an effective life span of 10 years.
• For safety reasons, when the battery is depleted after 10 years of use, you will need to buy a new smoke detector and stop using your Eve Smoke. Then, you can have it recycled along with other electronic waste.

• Eve Smoke is not available in North America.
• It is not designed or certified for use in North America.
• Eve Smoke will not be available in Canada, Mexico, or the United States.
• It is available in certain European countries, starting with Germany.

Make sure that known good batteries are inserted and that Eve Thermo is switched on. On the side of the device, under the battery compartment, there is a reset button. Use a paper clip or similar object to press the reset button until the digits 66/99 flash.

How to set up Eve Thermo including the Offset

Important note: The temperature displayed below Target Temperature in Eve is measured by Eve Thermo way too close to the heater, please ignore it. Once an Offset is set, it will not be integrated here.

To set up Eve Thermo open the app Eve and go to: Settings > Accessories > Eve Thermo Set Temperature Offset to 0 degrees. Then in Eve go to: Rooms > Eve Thermo and open Eve Thermo. Set Target Temperature to 23 degrees for example and let it heat for 2-3 hours. Then measure the temperature in the middle of the room with a thermometer, Eve Degree or Eve Room. If it reads for example 20,5 degrees, goto Settings > Accessories > Eve Thermo and set the Temperature Offset to -2,5 degrees.

You may have to adjust this over the next days a bit. As stated before, the Temperature Offset is not taken into account in the temperature shown below Target Temperature.

Please try the following step-by-step procedure including the trick with the 2 cent coin. We have learned that around 10% of the valves used have a slightly too small stroke, the coin compensates for this. If it works with the coin, we will gladly send you a mini adapter, which is put over the pin of the valve and compensates the stroke.

1. Delete Eve Thermo from Eve app

2. Un-mount Eve Thermo and make sure that you can move the valve on heater side (if not use grease and eventually hit the valve's body with a hammer to solve the problem)

3. Put new batteries in Eve Thermo ("E[x]" means either calibration problem or discharged batteries)

4. Hard reset Eve Thermo until the 66/99 appears on the LED.

5. Press one of the arrow on screen until "E[x]" disappears (the screen will then show "no", which means "mounting" and the valve will move to a correct mounting position)

6. Re-pair Eve Thermo in Eve app and follow instructions to mount it and calibrate it.

7. Insert a 2 cent coin into the valve holder of Eve Thermo.

8. Follow the assembly and calibration instructions.

If the code "E[x] does not appear on the display of the Eve Thermo during step 5, please skip this step.

Codes:

Alongside Bluetooth, Eve Thermo supports Thread. This technology makes your smart home network more responsive, robust, and increases its reach – the only thing you need is a HomePod mini or the new Apple TV 4K. Battery-operated Thread accessories, such as Eve Thermo, represent endpoints in your Thread network. 

By contrast, mains-powered Full Thread Devices (or FTDs) that are always on, such as Eve Energy and Eve Light Switch (Europe), can act as router nodes within your Thread network and relay data packets. So, the more of these Full Thread Devices (FTDs) you have in your network, the more stable and greater its reach becomes. Learn more

Definitely not. Eve Thermo is designed so you can fit it yourself: Simply unscrew your existing thermostat using your fingers (use a wrench if necessary), screw on Eve Thermo, and set it up in just a few steps using the Eve app. And there’s no need to sweat about swapping thermostats as there’s zero chance of water escaping. Watch the installation video.

No. With Eve, you can use all the features whenever you want without needing to register or subscribe. 

Yes. AA batteries keep Eve Thermo powered even in the event of a power outage. Eve Thermo doesn’t use cloud-based technology either – instead, it communicates directly with your iPhone or HomeKit home hub. And even when your iPhone isn’t within range, Eve Thermo will continue to work autonomously using the schedules you added thanks to these being stored on the accessory itself. You can also control Eve Thermo manually whenever you want.

Use a paper clip or similar object to press until the red LED is blinking 5 times.

You can use the Eve app to check that Eve Water Guard is working perfectly - with a soft alarm that’s gentle on the ears.
 

In case of a real alarm, Eve Water Guard will alert you immediately with its 100 dB siren and red flashing warning light. After one minute, the alarm sound will automatically pause and resume every two minutes for 10 seconds. If configured in the Apple Home App, you will also receive a notification.
 

You can mute Eve Water Guard using the Eve app – even if you’re away from home, provided you have a home hub. Muting an alarm using the Apple Home app is not possible. The alarm can also be stopped by unplugging the sensing cable.
 

After a water leak, Eve Water Guard will continue to report a leak as long as the sensing cable is wet. Eve Water Guard will continue normal operation once the sensing cable is fully dry.
 

The acoustic and visual alarm of Eve Water Guard cannot be deactivated.

• Sensing cable measures 2 m in length
• Several cables can be added to a total length of 150 m/500 ft (sold on our Official Website, once you click  "buy now".)
• Eve Water Guard leak detector required (sold separately)
• Avoid expensive water damage: Eve Water Guard detects water leaks, and alerts you the moment they occur- acoustically with its 100 dB siren, visually by a red flashing warning light and notifies you via iPhone, iPad or Apple Watch

Alongside Bluetooth, Eve Water Guard supports Thread. This technology makes your smart home network more responsive, robust, and increases its reach – the only other thing you need is a HomePod mini or the new Apple TV 4K. 

Mains-powered Thread accessories that are always on, such as Eve Water Guard and Eve Energy (Europe, U.K., U.S. & Canada) can act as router nodes within your Thread network and relay data packets. So, the more of these Full Thread Devices (FTDs) you have in your network, the more stable and greater its reach becomes. By contrast, battery-operated Thread accessories, such as Eve Aqua, Eve Door & Window, Eve Room, Eve Thermo and Eve Weather represent endpoints in the Thread network (or Minimal Thread Devices – MTDs). Learn more

Eve Water Guard alerts as soon as water comes into contact with even just a small section of the sensing cable. And as Eve Water Guard connects via Bluetooth or Thread on demand, you’ll be notified practically instantaneously via your iPhone that water is leaking out – saving you precious time and avoiding costly damage, as you won’t have to wait for a connection interval that many other devices on the market use.

Eve Water Guard lets you monitor any area where a water leak is likely to occur – no matter where your power outlet is located. That’s because you can just plug additional elements into the sensing cable, enabling you to reach even faraway places. The added benefit for you is that you don’t just end up monitoring a small section of the room, but can accurately lay the sensing cable to monitor entire areas. Visit the Eve Store to buy extensions for the sensing cable.

Press and hold the button for 10 seconds to reset Eve Weather.

Alongside Bluetooth, Eve Weather supports Thread. This technology makes your smart home network more responsive, robust, and increases its reach – the only thing you need is a HomePod mini or the new Apple TV 4K. Battery-operated Thread accessories, such as Eve Weather, represent endpoints in your Thread network. 

By contrast, mains-powered Thread accessories that are always on, such as Eve Energy (Europe, U.K., U.S. & Canada) and Eve Light Switch (Europe), can act as router nodes within your Thread network and relay data packets. So, the more of these Full Thread Devices (FTDs) you have in your network, the more stable and greater its reach becomes. Learn more 

Use a paper clip or similar object to press until the red LED is blinking 5 times.

No, you’ll need to screw in Eve Window Guard as the double-sided tape won’t be strong enough to hold it in place.

Eve Window Guard fits all euro-profile windows. For the sensor to fit, there needs to be at least 9 mm of clearance between the sash and the frame.

You’ll need one Eve Window Guard per window handle. If your double-sash window has one handle, you’ll only need one Eve Window Guard.